If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by BEI Design on September 12, 2009, 8:12 pm
The faux painting of my "faux rock" fireplace is going well,
but taking a whole lot more time than I expected. The new
hardwood floors are FABULOUS! Most of my LR furniture is
back in place, along with one of the new rugs, the other
two will stay safely stored until all the painting is done..
However...
A couple of weeks ago, I was rearranging stuff in the
unfinished basement in order to make room to store a
soon-to-be-unused teak media cabinet. I happened to go into
the furnace - hot water heater room for something. And
noticed a puddle of rusty water at the base of the
38-year-old natural gas water heater. And a decidedly nasty
looking rusty, bubbly, spot on the side of the tank, near
the bottom.
I got right on to my favorite plumbing company, they had a
new one installed early the following week. While he was
here anyway, and because I'm not a big fan of their $75.
minimum charge for piddley little jobs, I asked him to
replace the flex hose to the icemaker with copper tubing,
and to remove and install a new hot-water shut-off under the
kitchen sink. It had reached the point where I had NO hot
water pressure at the sink (and it wasn't the mixer, as that
has been replaced recently), figured it was an excellent
time to do something about that issue. So while he had the
whole-house water supply turned off anyway, he removed (with
some major effort) the short length of water pipe coming out
of the wall, and put in a new shut-off valve. HOWEVER, he
showed me the old 4" length of pipe which comes out of the
wall for the hot water supply. The 1/2" - 5/8"(?)
inside-diameter pipe had MAYBE 1/4" opening remaining. It
was almost full of rust, gunk, tiny gravel, whatever...
When he turned the water supply back on, every tap in the
house ran rusty water for a good long time. On the up side,
I always test nice and high for iron when I donate blood....
He strongly suggested I think about replacing ALL the
show/hide quoted text
galvanized water lines. <sigh>
On the bright side, the 50 gallon energy-efficient water
heater works well, I oversized it for me but it will be
perfect if/when I sell this three bathroom house. And the
copper tubing replacement to the ice maker went smoothly. I
dumped out the first couple of batches of rusty ice cubes.
Life is good... I think.... sewing soon... I hope....
--
Beverly
http://ickes.us/default.aspx
|
|
Posted by Juno B on September 12, 2009, 9:09 pm
BEI Design wrote:
show/hide quoted text
> The faux painting of my "faux rock" fireplace is going well,
> but taking a whole lot more time than I expected. The new
> hardwood floors are FABULOUS! Most of my LR furniture is
> back in place, along with one of the new rugs, the other
> two will stay safely stored until all the painting is done..
>
> However...
>
> A couple of weeks ago, I was rearranging stuff in the
> unfinished basement in order to make room to store a
> soon-to-be-unused teak media cabinet. I happened to go into
> the furnace - hot water heater room for something. And
> noticed a puddle of rusty water at the base of the
> 38-year-old natural gas water heater. And a decidedly nasty
> looking rusty, bubbly, spot on the side of the tank, near
> the bottom.
>
> I got right on to my favorite plumbing company, they had a
> new one installed early the following week. While he was
> here anyway, and because I'm not a big fan of their $75.
> minimum charge for piddley little jobs, I asked him to
> replace the flex hose to the icemaker with copper tubing,
> and to remove and install a new hot-water shut-off under the
> kitchen sink. It had reached the point where I had NO hot
> water pressure at the sink (and it wasn't the mixer, as that
> has been replaced recently), figured it was an excellent
> time to do something about that issue. So while he had the
> whole-house water supply turned off anyway, he removed (with
> some major effort) the short length of water pipe coming out
> of the wall, and put in a new shut-off valve. HOWEVER, he
> showed me the old 4" length of pipe which comes out of the
> wall for the hot water supply. The 1/2" - 5/8"(?)
> inside-diameter pipe had MAYBE 1/4" opening remaining. It
> was almost full of rust, gunk, tiny gravel, whatever...
> When he turned the water supply back on, every tap in the
> house ran rusty water for a good long time. On the up side,
> I always test nice and high for iron when I donate blood....
>
> He strongly suggested I think about replacing ALL the
>
> On the bright side, the 50 gallon energy-efficient water
> heater works well, I oversized it for me but it will be
> perfect if/when I sell this three bathroom house. And the
> copper tubing replacement to the ice maker went smoothly. I
> dumped out the first couple of batches of rusty ice cubes.
>
> Life is good... I think.... sewing soon... I hope....
>
You may not be sewing but your house will be in great shape and if you
replace the galvanized pipe you'll have great water pressure and no more
rusty water anyplace.
Juno
|
| Similar Threads | Posted | | Newbie questions on a sewing machine and a simple sewing project. | March 5, 2007, 9:45 pm |
| Need Sewing Machine recommendation for sewing Sunbrella outdoor fabric | July 7, 2007, 10:27 am |
| Brother QuattroT 6000D: Now Even Sewing Machines Are HD [Sewing] (Gizmodo) | January 2, 2009, 7:01 am |
| Difference between alt.sewing and rec.crafts.textiles.sewing? | February 27, 2006, 3:34 pm |
| Short summer sewing poll on sewing.com | June 19, 2006, 10:24 am |
| Recent projects... Not all sewing. but sewing related! | May 21, 2009, 12:39 pm |
| NOt sewing, but sewing related......... | May 16, 2007, 8:29 pm |
| my first bit of sewing ! | December 22, 2005, 8:45 am |
| Fun sewing day! | August 10, 2006, 4:05 am |
| Sewing with fur | December 29, 2006, 11:52 pm |
|
|