|
Sewing Textiles - Sewing: clothes, furnishings, costumes, etc.
|
|
|
|
If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by Trish Brown on October 17, 2007, 6:39 am
Rob wrote:
show/hide quoted text
>> Rob wrote:
>>> Trousers (pants) are worn quite wide at the moment and also long,
>>> giving a large "break".
>>> Can anyone tell me how to do a hem (at the end of the leg!) which is
>>> "dropped"; that is, longer at the back than at the front.
>>> Due to the angle, the turned-in material no longer distributes itself
>>> evenly inside the leg.
>>> Any hints on how to cope with this?
>>> Thanks.
>> To give the front hem edge a little extra ease so that it can be
>> stitched without puckering the trousers, I sometimes undo part, perhaps
>> half, of the turned-up portion of the side seam and inseam seams and
>> spread them open just a little. If you do this it's a good idea to
>> secure the partially opened seams with a few whip stitches.
>> Doreen in Alabama
>
> Thank you all for your helpful replies. I will first try Doreen's
> method on an old pair!
> Joy, what does "facing the edge" mean in this context?
> TIA
>
Hee! I'm jumping in here because I faced a hem myself this morning! LOLOLOL!
Facing a hem is what you do when you've stupidly neglected to leave
enough excess fabric to turn up much of a hem (say you've only got 1/4"
to turn up, for example). In my case, I made two little nightdresses for
my great-nieces and *forgot to leave anything for hems!!!!* (I can't
believe I did that!)
Since I was running very low on the nightdress fabric (a 'Dora' satin
print), I just cut some strips of nice cotton voile and used that for my
'hems'. I sewed it onto the bottoms of the nighties, overlocked the raw
edge, pressed the stitched-on bit upward and then caught up the hem by
hand just as if it were a real hem.
Just cut a bit of fabric the length of the required hem and as deep as
you want your new hem to be. You place it, right sides facing, on the
outside of the hem and sew along where the extreme end of the garment
will be. Then, you turn it inside out, press the 'seam' you've made and
hem as usual.
I've used extra-wide bias tape for this purpose and it works very well,
especially for a slightly shaped garment, such as an A-line dress or
flared trouser legs. Careful pressing makes the difference, I find.
HTH
--
Trish Newcastle, NSW, Australia
|
|
Posted by Joy Beeson on October 17, 2007, 10:21 pm
When using facing to deal with a curved hem, you need to cut a facing
the same shape as the bottom of the trouser leg. (This is easy when
making from scratch, because you just copy the pattern used for
cutting the leg. When altering, you'll have to lay the leg on paper
and poke pins through the pants to make your facing pattern.)
When applying a bias-tape facing, as mentioned in the previous post,
you can get away with sewing a straight facing to a curved hem because
the tape is very narrow, and it stretches. (Try to ease it on when
the curve is concave, and stretch it a bit when the curve is convex.)
Another plan is to leave just a seam allowance at the hem, turn it to
the inside, then applique' something over the raw edge: bias tape,
narrow all-cotton twill tape (polyester tape doesn't have enough
give), rick-rack, seam binding, hemming lace, ribbon -- anything you
can find and like the looks of that will bend around the curve.
And that will stand up to being cleaned the same way as the pants.
Don't forget to wash it first, if the hem will ever get wet.
Joy Beeson
--
joy beeson at comcast dot net
http://roughsewing.home.comcast.net/ -- sewing
http://n3f.home.comcast.net/ -- Writers' Exchange
The above message is a Usenet post.
I don't recall having given anyone permission to use it on a Web site.
|
Page 2 of 2 << first < 1 2
| Similar Threads | Posted | | Hello All! In need of some advice... | February 29, 2008, 12:12 am |
| Need advice on purchase of new machine | December 21, 2005, 3:33 pm |
| Two-tone pleated skirt -- advice? | December 24, 2005, 11:00 am |
| Advice sought for fabric application/gluing problem please. | March 15, 2008, 3:49 pm |
| Decisions...decisions! Advice needed | November 28, 2007, 2:31 pm |
|
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>>> Trousers (pants) are worn quite wide at the moment and also long,
>>> giving a large "break".
>>> Can anyone tell me how to do a hem (at the end of the leg!) which is
>>> "dropped"; that is, longer at the back than at the front.
>>> Due to the angle, the turned-in material no longer distributes itself
>>> evenly inside the leg.
>>> Any hints on how to cope with this?
>>> Thanks.
>> To give the front hem edge a little extra ease so that it can be
>> stitched without puckering the trousers, I sometimes undo part, perhaps
>> half, of the turned-up portion of the side seam and inseam seams and
>> spread them open just a little. If you do this it's a good idea to
>> secure the partially opened seams with a few whip stitches.
>> Doreen in Alabama
>
> Thank you all for your helpful replies. I will first try Doreen's
> method on an old pair!
> Joy, what does "facing the edge" mean in this context?
> TIA
>